(3) COD Ghost, Vinyl Decal, AR-15 Lower Magwell Tactical Sticker, 5.56, Airsoft

Description

You get 3 of the
COD Ghost
decals in this listing.
Size is 1.5 inches tall.
Made in the hills of East Tennessee. I have different versions of the AR-15 lower magwell decals as well as ammo can decals in my
e
b
a
y
store.
The decal is die cut with no background meaning the background will be what ever color the decal is placed on. The decal is cut from premium outdoor vinyl and has an outdoor life expectancy of 5 to 7 years. The indoor life expectancy is pretty close to forever.
COLORS:
All color choices are pictured in the 2nd image of the listing. The default color is
Flat White
.
lf you would like a different color other than the default please message me via note to seller during the checkout process
. If I receive no note to seller then I will send
Flat White
as a default color.
NOTE:
Only one color choice per 3 pack. No multiple colors in one listing of 3 decals. If you buy multiple listings the colors can be different for each 3 pack.
SHIPPING:
Since decals are thin and to keep costs low all  decals will be mailed via USPS as regular first class mail
without
tracking in a 6x9 manila envelope.
Please don’t mistake this as junk mail and throw away!
I will send you a message when your order is packed and ready to be mailed along with a picture that shows your order and envelope so you know what to expect.
INSTALLATION:
Please follow all firearm safety procedures before, during, and after the installation process.
The decal will come with transfer tape on top of the decal to aid in installation
. In the shipping message I will also include a link to my private tutorial video that covers the installation process from start to finish.
Written directions below. Please note that I can not issue refunds due to installation errors. Make sure all oil is cleaned from the magwell before you attempt to stick the decal. Patience is the key when applying these type of decals.
WRITTEN INSTALLATION INSTRUCTIONS:
Each decal consists of three layers
.
The top clear layer is the transfer tape, the
bottom layer is the backing paper, and the
middle layer is the actual vinyl decal.
To apply follow these simple steps.
Step 1:
Preform a safety check to ensure the firearm is unloaded and safe to work with!
Step 2:
Clean the surface where the decal will be placed to make sure there is no dust, grease, or oil before application.
(After step 1 this is the most important step, decal adhesive and dirty surfaces don't mix very well and will result in decal failure.)
Step 3:
Before you start to peel the transfer tape and decal from the backing paper rub the transfer tape firmly all over with a credit card or finger nail to allow the transfer tape to get a better grip on the actual decal. This is done best laying on a smooth hard surface.
Step 4:
Slowly peel the transfer tape from the backing paper. Make sure the decal sticks to the transfer tape and not on the backing paper. Do this slowly and watch the decal closely to avoid any tears.
(If the parts of the decal are not sticking to the transfer tape then slowly lower that section of the transfer tape back down onto the decal and rub with a credit card or finger to allow the transfer tape to get a better grip on the decal)
Step 5:
Position and stick the one edge of the transfer tape onto the target surface and slowly work the transfer tape down using a credit card or finger nail to work out any air bubbles as you work the decal onto the surface from the edge down.
(There is many different techniques to do this step on YouTube but this is the one I use most)
Step 6:
Now with the decal and transfer tape on the target surface take a credit card or finger and firmly rub the transfer tape to allow the decal to grip the target surface better.
(Sometimes leaving the two layers on awhile and rubbing the transfer tape a few times will allow the decal to get a better grip on the target surface. This is highly recommended if the target surface is wood, drywall, plastic or any other not very "smooth as glass" surface)
Step 7:
Slowly peel off the transfer tape from the target surface leaving the decal behind. Start at one corner and pull back at a very low angle. Make sure the decal sticks to the target surface and does not come up with the transfer tape.
(If the parts of the decal are not sticking to the target surface then slowly lower that section of the transfer tape back down onto the target surface and rub with a credit card or finger to allow the decal to get a better grip on the target surface)
Step 8:
Admire your new decal! And show your friends!
(If you apply your decal on a car be careful about pointing high pressure spray directly at the decal)
I have other AR-15 Magwell Decals and ammo can decals in my
e
b
a
y
store. Check them out!
Have a great day and thanks for looking!
Notice:
No
F
irearms
,
F
i
rearm
parts
,
Magazines
,
or
Firearm
accessories
are
sold
in
this
listing
.
All
Firearms
,
Firearm
parts
,
Magazines
,
or
Firearm
accessories
picture
d
are
for
display
purposes
only
and
are
to
show
the
decal
size
in
a
more
accurate
setting
.